Teledyne CETAC - Model U5000AT+ - Ultrasonic Nebulizer for ICP-AES/ICP-MS
From Nebulizers
The U5000AT+ Ultrasonic Nebulizer offers up to 10x lower element detection limits for ICP-AES and ICP-MS. Samples are introduced onto a highly efficient piezoelectric transducer, providing greater sample transport efficiency to the ICP.
-
Most popular related searches
Details
AutoTune Power Supply
CETAC's AutoTune Power Supply automatically senses changes in sample composition to ensure uniform and consistent aerosol generation. This AutoTune feature permits continuous use of the nebulizer even in the absence of a sample, allowing unattended operation.
Efficient Desolvation System
The U5000AT+ features a built-in desolvation system with a Peltier-cooled condenser. Dedicated teperature controllers allow fine adjustment of heater and condenser temperatures for best analytical performance. See schematic at right.
Detection Limits
Detection limits obtained with the U5000AT+ on ICP-AES are listed below for both radial and axial ICP torch configurations. Detection limits are improved in a range of 5 to 25 times, depending upon the analyte. The U5000AT+ may also be coupled with an ICP-MS, providing sub-ppt detection limits for many elements, particularly the platinum group elements (PGEs), the rare earth elements (REEs) and the actinides.
Utilizing the U5000AT+ for Aqueous Samples by ICP-AES
The CETAC U5000AT+ improves detection limits on any ICP-AES by factors of 5 to 25. This improvement in ICP-AES detection limits allows the transfer of significant amounts of work from Graphite Furnace AA to ICP-AES, where sample throughput is much greater.
Signal Stability
Long-term (10-hour) signal stability with the U5000AT+ for 500µg/L Pb spiked into drinking water is shown in the chart at right. Note the average stability is excellent at 0.40% RSD. (Each data point represents the mean of 180 ten-second measurements.) No internal standard was used in the stability experiment.
Signal Stabilization and Sample Rinse-Out
Signal stabilization, (Click figure on right), with the U5000AT+ is rapid, with signal reaching its plateau approximately 12 seconds after the sample reaches the ultrasonic transducer. Sample rinse-out is also fast, with the analyte concentrations decreasing to background levels after approximately 25 seconds. Sample and rinse solution (1% HNO3) uptake rate was 2.0 mL/min.
Modular Design
The CETAC U5000AT+ is equipped with a modular nebulizer/desolvation system. All wetted parts of the U5000AT+ are within this user removable module.
ICP-AES instrumentation allows users to measure elements at high (ppm) and low (ppb) concentrations. A second (optional) nebulizer/desolvation module may be used to alleviate sample memory effects and simplify nebulizer cleanup. Changeover from one module to another takes less than five minutes.
Specifications
- Sample Uptake Rate: 0.5 - 2.5 ml/min
- Nebulizer Gas Flow: 0.5 - 1.5 L/min
- Desolvation Heating Temp: 120ºC - 160ºC (Factory Setting: 140ºC)
- Desolvation Cooling Temp: -20ºC to 10ºC (Factory Setting: 3ºC)
- Power Requirements:
- 100 - 120VAC, 50-60Hz, 4.5A, 520W
- 220 - 240VAC, 50-60Hz, 2.5A, 520W
- Dimensions: 35.6 cm W x 34.9 cm D x 25.4 cm H
- Weight: 27 lbs (12.3 kg)
- Shipping Weight (With Cart and Accessories): 84 lbs (38.2 kg)
Nebulizer Features:
- Enhanced Sensitivity
- Simple and Efficient Operation
- Desolvating Capabilities
- Modular
Customer reviews
No reviews were found for Teledyne CETAC - Model U5000AT+ - Ultrasonic Nebulizer for ICP-AES/ICP-MS. Be the first to review!